Aerotech Ensemble HLe Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 112

background image

Installation and Configuration

Ensemble HLe

2.3.6. Brake Output (J207)

The Brake Output pins provide a direct connection to either the solid state relay on the Ensemble HLe or the
mechanical relay on the optional -IO board. The brake output pins in J207 permit the brake to be wired with
other signals in the feedback cable. The brake is configured for automatic or manual control using controller
parameters (refer to the Ensemble Help file for more information).

Use either the solid state relay on the Ensemble HLe or the mechanical relay on the -IO board when
connecting a power supply to the brake outputs on J207. Do not use both relays at the same time.

Refer to

for more information on using the brake output with the solid-state relay.

Refer to

for more information on using the brake output with the mechanical relay.

Table 2-18:

Brake Output Pins on the Motor Feedback Connector (J207)

Pin#

Description

In/Out/Bi

13

Brake Output -

Output

25

Brake

Output

www.aerotech.com

Chapter 2

49

«
...
47
48
49
50
51
...
»

Содержание Ensemble HLe

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Ensemble HLe

Бренд: Rayrun Страницы: 2

Бренд: IDenticard Страницы: 2

Бренд: 3Ware Страницы: 2

Бренд: Parker Страницы: 30

Бренд: VAT Страницы: 22

EtherNetIP ControlPlex CPC12EN

Бренд: E-T-A Страницы: 28

Бренд: Fancom Страницы: 31

Бренд: 3M Страницы: 90

Бренд: Galaxy Control Systems Страницы: 5

Бренд: WABCO Страницы: 4

Бренд: Rayrun Страницы: 4

Бренд: Parker Страницы: 29

Бренд: ZKTeco Страницы: 43

HydroTap G5 Touch-Free Wave

Бренд: Zip Страницы: 24

Бренд: V2 Страницы: 12

Бренд: H3C Страницы: 5

NORA-W10 Series

Бренд: u-blox Страницы: 56

Бренд: z21 Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды