Aerotech Ensemble HLe Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 112

background image

32

Chapter 2

www.aerotech.com

2.2.2.1. DC Brush Motor Phasing

A properly phased motor means that the positive motor lead should be connected to the ØA motor terminal
and the negative motor lead should be connected to the ØC motor terminal. To determine if the motor is
properly phased, connect a voltmeter to the motor leads of an un-powered motor:

1. Connect the positive lead of the voltmeter to the one of the motor terminals.

2. Connect the negative lead of the voltmeter to the other motor terminal.

3. Rotate the motor clockwise by hand.

Figure 2-9:

Clockwise Motor Rotation

4. If the voltmeter indicates a negative value, swap the motor leads and rotate the motor (CW, by hand)

again. When the voltmeter indicates a positive value, the motor leads have been identified.

5. Connect the motor lead from the voltmeter to the ØA motor terminal on the Ensemble HLe. Connect the

motor lead from the negative lead of the voltmeter to the ØC motor terminal on the Ensemble HLe.

N O T E :

If using standard Aerotech motors and cables, motor and encoder connection adjustments are

not required.

Ensemble HLe

Installation and Configuration

«
...
30
31
32
33
34
...
»

Содержание Ensemble HLe

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Ensemble HLe

Бренд: E-fly Страницы: 16

Бренд: Jafar Страницы: 10

Бренд: Eaton Страницы: 12

Бренд: Samson Страницы: 8

Бренд: Samson Страницы: 60

Бренд: Samson Страницы: 40

Бренд: micro-trak Страницы: 44

Бренд: RKC INSTRUMENT Страницы: 10

Red Atom PETRA01

Бренд: Perenio Страницы: 24

Бренд: Apex Toys Страницы: 7

Waukesha Cherry-Burrell D4 Series

Бренд: SPX FLOW Страницы: 34

OPTISWITCH 5100 C

Бренд: KROHNE Страницы: 40

Бренд: Vent-Axia Страницы: 4

Level-Trac LT-310

Бренд: QTS Страницы: 12

FLECK 5810 XTR2

Бренд: Pentair Страницы: 36

Бренд: OLYS Страницы: 4

The Boost Box WS 1107

Бренд: Watersports Innovations Страницы: 12

Бренд: Parker Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды