Aerotech Ensemble HLe Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 112

background image

Installation and Configuration

Ensemble HLe

Chapter 2: Installation and Configuration

2.1. Power Connections

The Ensemble HLe has two AC input connectors; one for control power and a second for motor power. For a
complete list of electrical specifications, refer to

N O T E :

The machine integrator, OEM or end user is responsible for meeting the final protective ground-

ing requirements of the system.

2.1.1. Control Supply Connections

N O T E :

This product requires two power supply connections. The Motor Supply and Control Supply

must both be connected for proper operation.

The control power supply input allows the Ensemble HLe to maintain communications if the motor power is
removed, such as in an Emergency Stop condition. The control power supply requires a minimum of 85 VAC
input to operate properly. The AC1 input is internally fused. The AC2 input is not internally fused but can be
connected to a voltage source other than Neutral if an external 2 A time-delay fuse is used.

Although the control power supply contains an internal filter, an additional external filter located as close as
possible to the Ensemble HLe may be required for CE compliance (Aerotech recommends Schaffner
FN2080).

Figure 2-1:

Control Supply Connections

Table 2-1:

Control Supply AC Input Wiring

Pin

Description

Recommended Wire Size

(1)

AC1

Line (L): 85-240 VAC Control Power Input

0.8 mm

2

(#18 AWG)

AC2

Neutral (0V) or 85-240 VAC Control Power Input with external fuse

0.8 mm

2

(#18 AWG)

Protective Ground (Required for Safety)

0.8 mm

2

(#18 AWG)

(1) Refer to local electrical safety requirements to correctly size external system wires.

Table 2-2:

Mating Connector Part Numbers for the Control Supply Connector

Type

Aerotech P/N

Phoenix P/N

Screw Torque

Value: Nm

Wire Size:

mm

2

[AWG ]

3-Pin Terminal Block

ECK00213

1754465

0.5 - 0.6

3.3 - 0.516 [12-30]

www.aerotech.com

Chapter 2

25

«
...
23
24
25
26
27
...
»

Содержание Ensemble HLe

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Ensemble HLe

Leroy-Somer R180

Бренд: Nidec Страницы: 20

Бренд: wattio Страницы: 20

Бренд: Babybee Страницы: 28

Бренд: Raymarine Страницы: 12

Бренд: Jafar Страницы: 13

Бренд: Nedap Страницы: 20

Бренд: York Страницы: 20

ZITON RADIO LOOP MODULE

Бренд: EMS Страницы: 26

Бренд: Danfoss Страницы: 30

Бренд: Gemini Страницы: 9

Бренд: M-system Страницы: 18

Бренд: M-system Страницы: 5

Бренд: Satel Страницы: 7

Бренд: Brooks Страницы: 66

Бренд: Z-Wave Страницы: 44

HydroGuard 1430 Series

Бренд: Powers Страницы: 8

Бренд: nano sensorics Страницы: 6

XBee DigiMesh 2.4

Бренд: Digi Страницы: 157

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды