manualshive.com logo in svg

Aerotech BL 10-40, Руководство по оборудованию

Поделиться
Скачать
Aerotech BL 10-40 Скачать руководство пользователя страница 45

Wiring Configurations

BL

3.4. Dual-Phase Command Configuration

In this configuration, the differential input, pre-amplifier, and self-commutation circuits are bypassed. The

dual-phase inputs are sinusoidal and are 120° out of phase from each other. The third phase is internally gen-

erated by the amplifier. The advantage of this configuration is that it provides the smoothest possible motion.

This mode is used with a brushless motor only.

Figure 3-4:

Dual-Phase Command Configuration

Table 3-3:

Dual-Phase Mode BL Configuration

Jumpers

1

Setting

Description

JP9

1-2 OUT, 3-4 IN, 5-6 OUT, 7-8 OUT

2

Dual phase mode

JP13

1-2 OUT, 3-4 IN, 5-6 OUT, 7-8 OUT

2

Dual phase mode

1. Refer to Section 4.1. Control Board Assembly for jumper locations

2. Default

Refer to Table 3-1 for complete Velocity Mode settings and Table 3-2 for complete Torque Mode settings.

www.aerotech.com

Chapter 3

35

Содержание BL 10-40





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды