manualshive.com logo in svg

Aerotech Automation1 XR3 Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Automation1 XR3 Series Скачать руководство пользователя страница 48

2.3.3. Thermistor Input

The thermistor input is used to detect a motor over temperature condition by using a positive
temperature coefficient sensor. As the temperature of the sensor increases, so does the resistance.
Under normal operating conditions, the resistance of the thermistor is low which will result in a low input
signal. As the increasing temperature causes the thermistor’s resistance to increase, the sensor will
trigger an over temperature fault.

The thermistor is connected between Pin 2 and Signal Common. The nominal trip value of the sensor is
1.385 kΩ. The circuit includes a 12 kΩ internal pull-up resistor which corresponds to a trip voltage of
+0.52 V.

Table 2-14:

Thermistor Input Pin on the Feedback Connector

Pin #

Description

In/Out/Bi

2

Motor Over Temperature Thermistor

Input

Figure 2-18:

Thermistor Input Schematic (Feedback Connector)

2.3.3. Thermistor Input

XR3 Hardware Manual

48

www.aerotech.com

Содержание Automation1 XR3 Series









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды