Aerotech Automation1 XL5e Скачать руководство пользователя страница 43

Страница: 43 / 110

2.3.2. Hall-Effect Inputs

The Hall-effect switch inputs are recommended for AC brushless motor commutation but not absolutely
required. The Hall-effect inputs accept 5 VDC level signals. Hall states (0,0,0) or (1,1,1) are invalid and will
generate a "Hall Fault" axis fault.

Refer to

Section 2.2.1.1.

for Hall-effect device phasing.

Table 2-18:

Hall-Effect Feedback Pins on the Feedback Connector

Pin #

Description

In/Out/Bi

+5V Power

(1)

N/A

Hall-Effect Sensor B (brushless motors only)

Input

Hall-Effect Sensor A (brushless motors only)

Input

Hall-Effect Sensor C (brushless motors only)

Input

+5V Power

(1)

N/A

Signal Common

N/A

Signal Common

N/A

(1) The maximum combined current output is 500 mA.

Figure 2-19:

Hall-Effect Inputs Schematic (Feedback Connector)

www.aerotech.com

XL5e Hardware Manual

2.3.2. Hall-Effect Inputs

Содержание Automation1 XL5e















































































































Результаты поиска

Содержание Automation1 XL5e

Отзывы:

Бренды по названию

Популярные бренды

Aerotech Automation1 XL5e, Руководство по оборудованию

Результаты поиска

Содержание Automation1 XL5e

Отзывы:

Бренды по названию

Популярные бренды