Aerotech Automation1 XI4-4P1 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 78

background image

2.5. HyperWire Interface

The HyperWire bus is the high-speed communications connection from the controller. It operates at
2 gigabits per second. The controller sends all command and configuration information through the
HyperWire bus.

HyperWire cables can be safely connected to or disconnected from a HyperWire port while the PC
and/or drive is powered on. However, any changes to the HyperWire network topology will disrupt
communication and you must reset the controller to re-establish communication.

WARNING

: Do not connect or disconnect HyperWire cables while you are loading

firmware or damage to the drives may occur.

Table 2-41:

HyperWire Card Part Number

Part Number

Description

HYPERWIRE-PCIE

HyperWire adapter, PCIe x4 interface

Table 2-42:

HyperWire Cable Part Numbers

Part Number

Description

HYPERWIRE-AO10-5

HyperWire cable, active optical, 0.5 m

HYPERWIRE-AO10-10

HyperWire cable, active optical, 1.0 m

HYPERWIRE-AO10-30

HyperWire cable, active optical, 3.0 m

HYPERWIRE-AO10-50

HyperWire cable, active optical, 5.0 m

HYPERWIRE-AO10-200

HyperWire cable, active optical, 20.0 m

iXI4/XI4 Hardware Manual

2.5. HyperWire Interface

www.aerotech.com

63

«
...
61
62
63
64
65
...
»

Содержание Automation1 XI4-4P1















































































Отзывы:

Нет отзывов

Похожие инструкции для Automation1 XI4-4P1

Бренд: Value Point Страницы: 7

Бренд: Garmin Страницы: 4

Бренд: Watts Страницы: 12

Бренд: Lancom Страницы: 8

Бренд: U-Prox Страницы: 3

DuetPro Carrycot

Бренд: Qtus Страницы: 52

Бренд: SYR Страницы: 2

Red Atom PETRA01

Бренд: Perenio Страницы: 24

Бренд: Grundfos Страницы: 16

Бренд: Loewe Страницы: 62

Бренд: Shimaden Страницы: 32

IntelliCross TouchFree Kit

Бренд: Novax Страницы: 3

Бренд: Daikin Страницы: 19

Бренд: Valence Tech Страницы: 12

Бренд: Dungs Страницы: 56

Бренд: Emec Страницы: 8

Бренд: Phoenix Contact Страницы: 56

Бренд: Hanma Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды