manualshive.com logo in svg

Aerotech Automation1 XC6e Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Automation1 XC6e Series Скачать руководство пользователя страница 96

5.1. Preventative Maintenance

Do an inspection of the XC6e and the external wiring one time each month. It might be necessary to do
more frequent inspections based on: 

l

The operating conditions of the system.

l

How you use the system.

Table 5-3:

Preventative Maintenance

Check

Action to be Taken

Examine the chassis for hardware and parts that
are damaged or loose.
It is not necessary to do an internal inspection
unless you think internal damage occurred.

Repair all damaged parts.

Do an inspection of the cooling vents.

Remove all material that collected in the vents.

Examine the work area to make sure there are no
fluids and no electrically conductive materials.

Do not let fluids and electrically conductive material
go into the XC6e.

Examine all cables and connections to make sure
they are correct.

Make sure that all connections are correctly
attached and not loose.
Replace cables that are worn.
Replace all broken connectors.

Cleaning

DANGER

: Before you clean the XC6e, disconnect the electrical power from the drive.

Use a clean, dry, soft cloth to clean the chassis of the XC6e. If necessary, you can use a cloth that is moist
with water or isopropyl alcohol. If you use a moist cloth, make sure that moisture does not go into the
XC6e. Also make sure that it does not go onto the outer connectors and components.

Do not use fluids and sprays to clean the XC6e because they can easily go into the chassis or onto the
outer connectors and components. If a cleaning solution goes into the XC6e, internal contamination can
cause corrosion and electrical short circuits.

Do not clean the labels with a cleaning solution because it might remove the label information.

5.1. Preventative Maintenance

XC6e Hardware Manual

96

www.aerotech.com

Содержание Automation1 XC6e Series















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды