Aerotech Automation1 XC6e Series Скачать руководство пользователя страница 11

Страница: 11 / 110

Safety Procedures and Warnings

IMPORTANT

: This manual tells you how to carefully and correctly use and operate the

XC6e drive.

Read all parts of this manual before you install or operate the XC6e drive or before
you do maintenance to your system.

To prevent injury to you and damage to the equipment, obey the precautions in this
manual.

All specifications and illustrations are for reference only and were complete and
accurate as of the release of this manual. To find the newest information about this
product, refer to www.aerotech.com.

If you do not understand the information in this manual, contact Aerotech Global
Technical Support.

IMPORTANT

: This product has been designed for light industrial manufacturing or

laboratory environments. If the product is used in a manner not specified by the
manufacturer:

The protection provided by the equipment could be impaired.

The life expectancy of the product could be decreased.

DANGER

: To decrease the risk of electrical shock, injury, death, and damage to the

equipment, obey the precautions that follow.

1. Before you do maintenance to the equipment, disconnect the electrical power.

2. Restrict access to the XC6e when it is connected to a power source.

3. Do not connect or disconnect electrical components, wires, and cables while this

product is connected to a power source.

4. Wait at least ten (10) minutes after removing the power supply before doing main-

tenance or an inspection. Otherwise, there is the danger of electric shock.

5. There are lethal voltages on the shunt resistor terminals.

6. Supply each operator with the necessary protection from live electrical circuits.

7. Make sure that all components are grounded correctly and that they obey the local

electrical safety requirements.

8. Install the necessary precautions to supply safety and protection to the operator.

DANGER

: System travel can cause crush, shear, or pinch injuries. Restrict access to all

motor and stage parts while your system is connected to a power source.

DANGER

: Hot surfaces. The case temperature could exceed 70°C.

XC6e Hardware Manual

Safety Procedures and Warnings

www.aerotech.com

Содержание Automation1 XC6e Series















































































































Результаты поиска

Содержание Automation1 XC6e Series

Отзывы:

Бренды по названию

Популярные бренды

Aerotech Automation1 XC6e Series, Руководство по оборудованию

Результаты поиска

Содержание Automation1 XC6e Series

Отзывы:

Бренды по названию

Популярные бренды