Aerotech Automation1 XC4e Скачать руководство пользователя страница 9

Страница: 9 / 122

EU Declaration of Conformity

Manufacturer

Aerotech, Inc.

Address

101 Zeta Drive
Pittsburgh, PA 15238-2811
USA

Product

XC4e

Model/Types

All

This is to certify that the aforementioned product is in accordance with the applicable requirements of
the following Directive(s):

2014/30/EU

Electromagnetic Compatibility (EMC)

2014/35/EU

Low Voltage Directive

2006/42/EC

Machinery Directive

EU 2015/863

Directive, Restricted Substances (RoHS 3)

and has been designed to be in conformity with the applicable requirements of the following Standard(s)
when installed and used in accordance with the manufacturer’s supplied installation instructions.

EN 61326-1:2013

EMC Requirements for Electrical Equipment

EN 61010-1:2010/A1:2019

Safety Requirements for Electrical Equipment

EN ISO 13849-1:2015

Safety Related Parts of Control Systems

Authorized Representative:

Simon Smith, European Director

Address:

Aerotech Ltd
The Old Brick Kiln, Ramsdell, Tadley
Hampshire RG26 5PR
UK

Name

/ Alex Weibel

Position

Engineer Verifying Compliance

Location

Pittsburgh, PA

Date

3/24/2021

XC4e Hardware Manual

EU Declaration of Conformity

www.aerotech.com

Содержание Automation1 XC4e



























































































































Результаты поиска

Содержание Automation1 XC4e

Отзывы:

Бренды по названию

Популярные бренды

Aerotech Automation1 XC4e, Руководство по оборудованию

Результаты поиска

Содержание Automation1 XC4e

Отзывы:

Бренды по названию

Популярные бренды