manualshive.com logo in svg

Aerotech Automation1 XC4e, Руководство по оборудованию

Поделиться
Скачать
Aerotech Automation1 XC4e Скачать руководство пользователя страница 43

2.2.2.1. DC Brush Motor Phasing

A properly phased motor means that the positive motor lead should be connected to the ØA motor
terminal and the negative motor lead should be connected to the ØC motor terminal. To determine if
the motor is properly phased, connect a voltmeter to the motor leads of an un-powered motor:

1. Connect the positive lead of the voltmeter to the one of the motor terminals.
2. Connect the negative lead of the voltmeter to the other motor terminal.
3. Move or rotate the motor in the positive or clockwise (CW) direction by hand.

Figure 2-16:

Positive Motor Direction

4. If the voltmeter indicates a negative value, swap the motor leads and move the motor by hand in

the positive direction, again. When the voltmeter indicates a positive value, the motor leads have
been identified.

5. Connect the motor lead from the positive lead of the voltmeter to the ØA motor terminal on the

XC4e. Connect the motor lead from the negative lead of the voltmeter to the ØC motor terminal
on the XC4e.

For Aerotech-supplied systems, the motor, encoder and Hall sensors are correctly configured and
connection adjustments are not necessary.

www.aerotech.com

43

XC4e Hardware Manual

2.2.2. DC Brush Motor Connections

Содержание Automation1 XC4e



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды