manualshive.com logo in svg

Aerotech Automation1 XC4e, Руководство по оборудованию

Поделиться
Скачать
Aerotech Automation1 XC4e Скачать руководство пользователя страница 27

Chapter 2: Installation and Configuration

Unpacking the Chassis

IMPORTANT

: All electronic equipment and instrumentation is wrapped in antistatic

material and packaged with desiccant. Ensure that the antistatic material is not damaged
during unpacking.

Inspect the container of the XC4e for any evidence of shipping damage. If any damage exists, notify the
shipping carrier immediately.

Remove the packing list from the XC4e container. Make sure that all the items specified on the packing
list are contained within the package.

The documentation for the XC4e is on the included installation device. The documents include manuals,
interconnection drawings, and other documentation pertaining to the system. Save this information for
future reference. Additional information about the system is provided on the Serial and Power labels
that are placed on the XC4e chassis.

The system serial number label contains important information such as the:

l

Customer order number (please provide this number when requesting product support)

l

Drawing number

l

System part number

XC4e Hardware Manual

Chapter 2: Installation and Configuration

www.aerotech.com

27

Содержание Automation1 XC4e



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды