manualshive.com logo in svg

Aerotech Automation1 XC4e, Руководство по оборудованию

Поделиться
Скачать
Aerotech Automation1 XC4e Скачать руководство пользователя страница 108

5.1. Preventative Maintenance

Do an inspection of the XC4e and the external wiring one time each month. It might be necessary to do
more frequent inspections based on: 

l

The operating conditions of the system.

l

How you use the system.

Table 5-3:

Preventative Maintenance

Check

Action to be Taken

Examine the chassis for hardware and parts that
are damaged or loose.
It is not necessary to do an internal inspection
unless you think internal damage occurred.

Repair all damaged parts.

Do an inspection of the cooling vents.

Remove all material that collected in the vents.

Examine the work area to make sure there are no
fluids and no electrically conductive materials.

Do not let fluids and electrically conductive material
go into the XC4e.

Examine all cables and connections to make sure
they are correct.

Make sure that all connections are correctly
attached and not loose.
Replace cables that are worn.
Replace all broken connectors.

Cleaning

DANGER

: Before you clean the XC4e, disconnect the electrical power from the drive.

Use a clean, dry, soft cloth to clean the chassis of the XC4e. If necessary, you can use a cloth that is moist
with water or isopropyl alcohol. If you use a moist cloth, make sure that moisture does not go into the
XC4e. Also make sure that it does not go onto the outer connectors and components.

Do not use fluids and sprays to clean the XC4e because they can easily go into the chassis or onto the
outer connectors and components. If a cleaning solution goes into the XC4e, internal contamination can
cause corrosion and electrical short circuits.

Do not clean the labels with a cleaning solution because it might remove the label information.

5.1. Preventative Maintenance

XC4e Hardware Manual

108

www.aerotech.com

Содержание Automation1 XC4e



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды