manualshive.com logo in svg

Aerotech Automation1 iXL2e, Руководство по оборудованию, Страница: 43 / 96

Поделиться
Скачать
Aerotech Automation1 iXL2e Скачать руководство пользователя страница 43

2.3.3. Thermistor Input

The thermistor input is used to detect a motor over temperature condition by using a positive

temperature coefficient sensor. As the temperature of the sensor increases, so does the resistance.

Under normal operating conditions, the resistance of the thermistor is low which will result in a low

input signal. As the increasing temperature causes the resistance of the thermistor to increase, the

sensor will trigger an over temperature fault.
The thermistor is connected between Pin 2 and Signal Common. The nominal trip value of the sensor

is 1.385 kΩ. The circuit includes a 12 kΩ internal pull-up resistor which corresponds to a trip voltage

of +0.52 V.

Table 2-18:

Thermistor Input Pin on the Feedback Connector

Pin # Description

In/Out/Bi

2

Motor Over Temperature Thermistor

Input

Figure 2-20:

Thermistor Input Schematic (Feedback Connector)

Hardware Manual

iXL2e/XL2e

www.aerotech.com

43

Содержание Automation1 iXL2e

































































































Отзывы:

Нет отзывов