Aerotech Automation1 iXL2e Скачать руководство пользователя страница 29

Страница: 29 / 96

2.2. Motor Power Output Connector

DANGER

: Before you do maintenance to the equipment, disconnect the electrical

power. Wait at least one (1) minute after removing the power supply before doing

maintenance or an inspection. Otherwise, there is the danger of electric shock.

The drive can be used to drive the following motor types:

Brushless (refer to

Section 2.2.1.

)

DC Brush (refer to

Section 2.2.2.

)

Stepper (refer to

Section 2.2.3.

)

For a complete list of electrical specifications, refer to

Section 1.1.

DANGER: Shock and Fire Hazard

Electrical wiring must be designed and installed in accordance with local electrical

safety regulations to prevent the risk of fire and electrical shock.

The 8-pin terminal block style motor output connector is located on the front panel.

Table 2-5:

Motor Power Output Connector Pinout

Pin

Description

Connector

Earth Ground to Motor

Brushless Phase A Motor Lead
DC Brush +
Stepper

Brushless Phase B Motor Lead
Stepper

Brushless Phase C Motor Lead
DC Brush -
Stepper Return

Table 2-6:

Motor Power Output Mating Connector Ratings

Specification

Description

Type

8-Pin Terminal Block

Part Numbers

Aerotech: ECK02625

Phoenix: 1839694

Conductor Cross

Section

One conductor, stranded with ferrule

and plastic sleeve

18...22 AWG (0.25...0.75 mm

)

Two conductors (same cross-

section), stranded , twin ferrule with

plastic sleeve

20 AWG (0.5 mm

)

Tightening Torque

0.22...0.25 N·m

Conductor Insulation Strip Length

7 mm (0.25 in)

(1) Refer to the manufacturer website for additional information.

Hardware Manual

iXL2e/XL2e

www.aerotech.com

Содержание Automation1 iXL2e

































































































Результаты поиска

Содержание Automation1 iXL2e

Отзывы:

Aerotech Automation1 iXL2e, Руководство по оборудованию, Страница: 29 / 96

Результаты поиска

Содержание Automation1 iXL2e

Отзывы: