manualshive.com logo in svg

Aerotech Automation1 iXC2, Руководство по оборудованию

Поделиться
Скачать
Aerotech Automation1 iXC2 Скачать руководство пользователя страница 13

Handling and Storage

Unpacking the drive

IMPORTANT

: All electronic equipment and instrumentation is wrapped in antistatic

material and packaged with desiccant. Ensure that the antistatic material is not
damaged during unpacking.

Inspect the shipping container for any evidence of shipping damage. If any damage exists, notify the
shipping carrier immediately.

Remove the packing list from the shipping container. Make sure that all the items specified on the
packing list are contained within the package.

The documentation for the drive is on the included installation device. The documents include
manuals, interconnection drawings, and other documentation pertaining to the system. Save this
information for future reference. Additional information about the system is provided on the Serial
and Power labels that are placed on the chassis.

The system serial number label contains important information such as the:

l

Customer order number (please provide this number when requesting product support)

l

Drawing number

l

System part number

Handling

IMPORTANT

: It is the responsibility of the customer to safely and carefully lift and

move the drive.

l

Be careful when you move or transport the drive.

l

Refer to

Section 1.2. Mechanical Specifications

for dimensions and weight spe-

cifications.

l

Retain the shipping materials for future use.

l

Transport or store the drive in its protective packaging.

WARNING: Electrostatic Discharge (ESD) Sensitive Components!

You could damage the power supply or drives if you fail to observe the correct
ESD practices.

Wear an ESD wrist strap when you handle, install, or do service to the system assembly.

Storage

Store the drive in the original shipping container. If the original packaging included ESD protective
packaging, make sure to store the drive in it. The storage location must be dry, free of dust, free of
vibrations, and flat.

Refer to

Section 1.3. Environmental Specifications

.

Hardware Manual

iXC2/XC2

www.aerotech.com

13

Содержание Automation1 iXC2

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды