Aeroqual AQM60 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 83

Aeroqual AQM60 Скачать руководство пользователя страница 13

Page | 13

Aeroqual AQM60 User Guide

A programming port is also exposed through the side of the module to allow custom programs to be loaded
into the module.

Note 1: Aeroqual can supply a standard programming tool for distributors to reprogram the auxiliary
module to the specified requirements.

Note 2: Please refer to third party sensor manuals for instructions on wire outputs. The Wind Sonic
comes with an Aeroqual supplied cable and therefore wire outputs will be sent with the cable.

1.10. Particle Mass Pump Modules

The Pump Modules for the optical mass sensors contain a microprocessor for mass calculation and a pump
for sampling. There is a different pump module for the Nephelometer and optical particle counter (Profiler)
sensor modules

1.10.1.

Profiler Pump Module

1.10.2.

Nephelometer Particle Monitor

Purge line

Exhaust line with
flow adjuster

Inlet heater connector

RS232 connector from
optical engine.

12VDC power
connection

RS485 termination
dongle

RS485 bus cable

Sample line

Power on LED

Inlet heater connector

Cable from optical engine

12VDC power
connection

RS485 termination dongle

RS485 cable

Exhaust line with flow
adjuster

Power on LED

Sample in

Sheath air out with
flow adjuster

Fibre span switch

«
...
11
12
13
14
15
...
»

Содержание AQM60




















































































Отзывы:

Нет отзывов