Aeroqual AQM60 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 83

Aeroqual AQM60 Скачать руководство пользователя страница 10

Page | 10

Aeroqual AQM60 User Guide

1.5. Compressor

The cooling system is a compressor refrigeration unit which is mounted at the base of the AQM60. It is a
self-contained system that provides cooling via the base on the AQM. The compressor system and inlet can
be accessed by releasing the two clips on the side of the AQM and rotating the housing upwards.

1.6. Power Module

Two Meanwell HLG240-12A 192W 12V Single Output Class 2 with PFC Power Units are mounted on the
outside of the enclosure. One powers the compressor and the second powers the modules. It has features
including universal AC input (90-280VAC) and IP65 rating.

1.7. Humidity and Temperature Sensor

The Humidity and Temperature Sensor is a Sensirion single chip device which contains a capacitive polymer
sensing element for relative humidity and a band-gap temperature sensor. More detailed specifications are in
the table below. The temperature and humidity sensor is housed in a connector located on the bottom of the
enclosure. It is connected directly to the Control Module.

Humidity

Resolution

0.1 %RH

Range

0 to 100 %RH

Temperature

Resolution

0.1 °C

Range

-40 to 120 °C

Temperature &
Relative Humidity
Sensor

Compressor

Junction box for
mains connection

«
...
8
9
10
11
12
...
»

Содержание AQM60




















































































Отзывы:

Нет отзывов