Aeroqual AQM 65 Скачать руководство пользователя страница 31

Страница: 31 / 127

MRK-D-0034 V2.0

Aeroqual AQM 65 User Guide

Page | 30

2.2.4 Wire external third party sensors

Online

reference

training.aeroqual.com AQM 65 technical training Section 2.5

Online video

https://vimeo.com/130818560



External sensors such weather stations and noise meters need to be wired to the green
connector plug on the front of the auxiliary module.



Each third party sensor requires a different wiring configuration.



The correct wiring configuration for each sensor is given in the online training

NOTE:

To check the operation of the third party sensor in your office or laboratory prior to site

installation it is not required to feed the cable through the gland.

Figure 2-12 To connect third party sensors such as weather sensors, feed the cable through the gland
and wire to the green plug.



If you are happy with the wiring then apply power, and log on to the Aeroqual Connect
software. After some minutes you should see the parameters associated with the third party
sensor being shown in the software.

Содержание AQM 65
































































































































Результаты поиска

Содержание AQM 65

Отзывы:

Aeroqual AQM 65, Руководство пользователя, Страница: 31 / 127

Результаты поиска

Содержание AQM 65

Отзывы: