BATHROOM FAN
www.aeropurefans.com
MODEL: VSF110D-S
WARNING
WARNING- TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, PLEASE READ
THE FOLLOWING PRIOR TO INSTALLING THE FAN:
1
. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.
2
. Before
servicing or cleaning unit, switch power off at service panel to prevent power from being switched on accidentally. When the
service disconnect cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
3
. Installation work and electrical wiring must be done by a licensed person(s) in accordance with all applicable codes and
standards, including fire-rated construction codes and standards.
4
. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdraft. Follow the heating equipment
manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and
the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
5
. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
6
. Ducted fans must
always be vented to the outdoors.
7
.Unit is acceptable for use over a tub or shower when connected to a GFCI (Ground Fault
Circuit Interrupter) protected branch circuit (ceiling installation only).
8
. This unit must be grounded.
9
. Not for use in kitchens.
10
. Install fan at least 2.5 m (8.2 feet) above the floor.
11
. To reduce risk of fire and to properly exhaust air, be sure to duct air
outside. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages. This unit is
appropriate for wall installation in a non-wet application.
12
. WARNING: To reduce the risk of fire or electric shock, do not use
this fan with any solid-state speed control device.
13
. The fan must not be installed in a ceiling thermally insulated to a value
greater than R40.
CAUTION
1
. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2
. This product is
designed for installation in ceilings up to a 12/12 pitch (45 degree angle). Duct connector must point upward for wall application.
3
. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power
unit.
4
. Please read specification label on product for further information and requirements.
*
The manual in electronic format may be downloaded from our company website or obtained from the dealer.
CLEANING & MAINTENANCE
For quiet and efficient operation, long life, and attractive appearance - lower or remove grille and vacuum interior of unit with the
dusting brush attachment.
The motor is permanently lubricated and never needs oiling.
OPERATION
User setting
The control box, located inside the fan housing, has one separate
adjustment: the toggle switch, which will adjust the upper fan speed
setting from 80 to 140 CFM.
Timer delay
Low airflow
knob
+ +
S
12
3
T
Power box
Toggle switch
Switch
position
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
Air deliver (CFM)
80 90 110 120 90 110 120 140
1 2 3
Duct
diameter
4"
4"
4"
4"
6"
6
"
6"
6"
(inches)
How to Work
To Turn Fan ON
Turn the Wall Switch (according to the follow
ing “CONNECT ELECTRICAL
WIRING”) ON.
.
Factory setting: 110CFM (
with 6" duct
)
To Turn Fan OFF
Turn the Wall Switch OFF
916, and 920.
Other airflow reference performance based on HVI
Procedures 915, 916, and 920.
READ AND SAVE THESE INSTRUCTIONS
Installer: Leave this manual with the homeowner.
1
Airflow
(CFM)
80 90 110 120 90 110 120 140
Duct
Diameter
(inches)
4” 4” 4” 4” 6” 6” 6” 6”
1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3