Housing
BATH FAN with Light
www.aeropurefans.com
MODEL: CP70-SL
WARNING
APPROVED FOR BOTH CEILING AND WALL INSTALLATION
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, PLEASE READ THE FOLLOWING:
1
. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address
or
telephone number listed in the warranty.
2
. Before servicing or cleaning unit, switch power off at service panel and lock the service
disconnecting means to prevent power from being switching on accidentally. If the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such as a tag, to the service panel.
3
. Installation work and electrical wiring must be done
by a licensed person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.
4
. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to
prevent backdra
ft. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the
National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
5
. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other
hidden utilities.
6.
Ducted fans must always be vented to the outdoors.
7
. Acceptable for use over a tub or shower when connected to a GFCI (Ground Fault Circuit Interrupter) protected branch
circuit.
8
. This unit must be grounded.
9
. Never place a switch where it can be reached from a tub or shower.
10
. Not for use in
kitchens.
11
. Install fan at least 2.5 m (8.2 feet) above the floor.
12
. WARNING: To reduce the risk of fire or electric shock, do
not use this
fan with any solid-state speed control device.
13
. The fan must not be installed in a ceiling thermally insulated to a
value greater than R40.
CAUTION
1
. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2
. This product is designed for installation in ceilings up to a 12/12 pitch (45 degree angle). Duct connector must point up for
wall
application.
3.
To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall and construction dust away of motor
unit.
4. Please read specification label on product for further information and requirements.
CLEANING & MAINTENANCE
For quiet and efficient operation, long life, and attractive appearance, lower or remove grille and vacuum interior of unit with
the dusting brush attachment.
The motor is permanently lubricated and never needs oiling.
OPERATION
The fan and light can be operated separately. Use a 2-function wall control. S
ee “Connect Wiring” for details.
ASSEMBLY INSTRUCTIONS
MOUNT DIRECTLY TO JOIST OR I-JOIST
Place the housing assembly in the opening so the bottom edge is flush with the finished ceiling. Nail the housing assembly to
the joist using nails.
POSITION THE HOUSING ASSEMBLY
Position the housing assembly against the joist. With a pencil,
trace an outline of the housing assembly onto the ceiling. Set
the housing aside, and cut out an opening for the fan.
Note:hold the housing position 5/16" above the ceiling edge.
Housing
Ceiling
5/16in.
CONNECT ELECTRICAL WIRING
Run 120 V AC house wiring to the location of the fan. Use only UL-approved connectors (not included) to attach the house wiring to the wiring plate.
Refer to the wiring diagram, and connect the wires as shown.
BLACK(BLK)
WHITE(WHT)
BLUE(BLU)
GROUND (GRD)
LIGHT
PANEL
WIRE
UNIT
FAN
FAN
RECEPTACLE
SWITCH BOX
LIGHT
RECEPTACLE
POWER SUPPLY
120V AC
READ AND SAVE THESE INSTRUCTIONS
Installer: Leave this manual with the homeowner.
Cod
：
0060301134
1
Ceiling
5/16in