AEMC instruments 6416 Скачать руководство пользователя страница 43

Страница: 43 / 48

Clamp-on Ground Resistance Tester Model 6416

8.3 REPAIR AND CALIBRATION

To ensure that your instrument meets factory specifications, we recommend that

it be sent back to our factory Service Center at one-year intervals for recalibration

or as required by other standards or internal procedures.

For instrument repair and calibration:

You must contact our Service Center for a Customer Service Authorization

Number (CSA#). Send an email to

[email protected]

requesting a CSA#,

you will be provided a CSA Form and other required paperwork along with the

next steps to complete the request. Then return the instrument along with the

signed CSA Form. This will ensure that when your instrument arrives, it will be

tracked and processed promptly. Please write the CSA# on the outside of the

shipping container. If the instrument is returned for calibration, we need to know

if you want a standard calibration or a calibration traceable to N.I.S.T. (includes

calibration certificate plus recorded calibration data).

Ship To:

Chauvin Arnoux

, Inc. d.b.a. AEMC

Instruments

15 Faraday Drive ▪ Dover, NH 03820 USA

Phone: (800) 945-2362 (Ext. 360) / (603) 749-6434 (Ext. 360)

Fax: (603) 742-2346 or (603) 749-6309

E-mail:

[email protected]

(Or contact your authorized distributor.)

to N.I.S.T.

NOTE: You must obtain a CSA# before returning any instrument.

8.4 TECHNICAL ASSISTANCE

If you are experiencing any technical problems or require any assistance with the

proper operation or application of your instrument, please call, mail, fax, or e-mail

our technical support team:

Chauvin Arnoux

, Inc. d.b.a. AEMC

Instruments

Phone: (800) 343-1391 (Ext. 351)

Fax:

(603) 742-2346

E-mail:

[email protected]

www.aemc.com

Содержание 6416

















































Результаты поиска

Содержание 6416

Отзывы:

Бренды по названию

Популярные бренды

AEMC instruments 6416, Руководство пользователя

Результаты поиска

Содержание 6416

Отзывы:

Бренды по названию

Популярные бренды