AEMC instruments 1015 Скачать руководство пользователя страница 20

Страница: 20 / 24

Megohmmeter Model 1015

5. MAINTENANCE

The device does not contain any parts that can be replaced by untrained

or unaccredited personnel. Any unauthorized work or part replacement

with equivalents may seriously compromise safety.

WARNING:

•

For maintenance use only specified replacement parts.

• To avoid electrical shock, do not attempt to perform any servicing unless

you are qualified to do so.

• To avoid electrical shock and/or damage to the instrument, do not get

water or other foreign agents into the case. Turn the instrument

OFF

and

disconnect the unit from all the circuits before opening the case.

5.1 BATTERY TEST

Check that the batteries are in good working condition prior to using the

instrument.

With the switch in the OFF position, press the yellow button:

• The batteries are good if the needle is in the green zone.
• The batteries need replacement if the needle is in the red zone or lower.

The average battery life is:

• 1000 insulation measurements of 10 s on the M

Ω

-500 V range for R = 500 k

Ω

• 200 insulation measurements of 10 s on the M

Ω

-1000 V range for R = 1 M

Ω

• 1500 continuity measurements of 10 s on the 10

Ω

range.

NOTE:

The instrument will operate correctly with a battery voltage

range of (4.5 to 6.5) V.

5.1.1 Battery and Fuse Replacement

0.1

0.5

5 10

50 100

500

1000

100

200

300

400

500

600V

Ω

RED zone or below:

Battery needs to be replaced

GREEN zone:

Battery is good

Содержание 1015

























Результаты поиска

Содержание 1015

Отзывы:

Бренды по названию

Популярные бренды

AEMC instruments 1015, Руководство пользователя

Результаты поиска

Содержание 1015

Отзывы:

Бренды по названию

Популярные бренды