AEM Performance Electronics CD-5 Carbon Скачать руководство пользователя | Manualshive

Страница: 20 / 120

background image

20

Wiring Schematic

Installing AEM DashDesign

AEM DashDesign is distributed as a single install executable. To install, run AEM DashDesign Setup.exe and follow
the on-screen instructions including those requiring you to restart your PC if necessary.

Installing USB Drivers

The installation program will automatically install the USB drivers required by AEM Dash. However, on rare
occasions, it may be necessary to install the USB drivers manually. To do this:

·

Connect the AEM Dash to the PC.

·

When the add new hardware wizard appears, select "Install from a list or specific location" and click Next.

·

Choose "Search for the best driver in these locations" and check "Include this location in the search"

·

Click the Browse button and navigate to the Drivers folder sub folder in the AEM DashDesign installation directory.

·

Click the Next button and the driver installation will proceed automatically.

Air/Fuel Sensors and Devices to Dash

The AEMNet CAN message transmission is enabled by default on the following devices. Refer to your harness
documentation to identify the CAN terminals.

«
...
18
19
20
21
22
...
»

Содержание CD-5 Carbon

























































































































Отзывы:

Нет отзывов

Похожие инструкции для CD-5 Carbon

Бренд: Y-cam Страницы: 12

Бренд: Danfoss Страницы: 4

Бренд: Waterpik Страницы: 2

Бренд: VTech Baby Страницы: 22

Бренд: DRO PROS Страницы: 2

Бренд: hepco & becker Страницы: 4

Бренд: Veho Страницы: 37

Бренд: Vega Страницы: 56

Бренд: Rola Страницы: 3

Docking Station for the Apple 13" MacBook

Бренд: Bookendz Страницы: 12

Бренд: StowAway 2 Страницы: 2

Бренд: Ohlins Страницы: 8

Бренд: Norcool Страницы: 16

Бренд: Webasto Страницы: 18

inView 360 Fusion

Бренд: Safe Fleet Страницы: 27

ROADSIDE ASSISTANCE

Бренд: Seat Страницы: 44

Бренд: Case-Mate Страницы: 5

Бренд: Boogie Board Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды