INSTALLATION INSTRUCTIONS
VALIANT SERIES POST TOP
American Electric Lighting a division of Acuity Lighting Group, Inc. Newark, OH
DRAWING NO. A67959 REV C
(FRONT)
©2008 ACUITY LIGHTING GROUP, INC.
PART NUMBER 057-71-67959
OPENING & CLOSING THE UNIT:
OPENING & CLOSING THE UNIT:
1. OPEN THE UNIT. (SEE “OPENING AND CLOSING THE UNIT”
1. OPEN THE UNIT. (SEE “OPENING AND CLOSING THE UNIT”
ABOVE.)
ABOVE.)
2. UNSCREW THE FOUR CAPTIVE SCREWS ATTACHING THE
2. UNSCREW THE FOUR CAPTIVE SCREWS ATTACHING THE
POWER PAD TO THE UNIT, TOTALLY DISENGAGING THEM
POWER PAD TO THE UNIT, TOTALLY DISENGAGING THEM
FROM THE CASTING. (SEE FIGURE 2). YOU WILL KNOW THE
FROM THE CASTING. (SEE FIGURE 2). YOU WILL KNOW THE
SCREWS CAN MOVE FREELY UP AND DOWN.
SCREWS CAN MOVE FREELY UP AND DOWN.
3. GRIPPING THE LAMP SOCKET & BRACKET, REMOVE THE
3. GRIPPING THE LAMP SOCKET & BRACKET, REMOVE THE
POWER PAD FROM THE UNIT, DISCONNECTING THE WIRING
POWER PAD FROM THE UNIT, DISCONNECTING THE WIRING
BY USE OF THE QUICK DISCONNECT. NOTE: ALTHOUGH NOT
BY USE OF THE QUICK DISCONNECT. NOTE: ALTHOUGH NOT
NECESSARY, REMOVING SOME OF THE FOUR LENS PANELS
NECESSARY, REMOVING SOME OF THE FOUR LENS PANELS
MAY MAKE IT EASIER TO ACCESS AND REMOVE THE POWER
MAY MAKE IT EASIER TO ACCESS AND REMOVE THE POWER
PAD.
PAD.
4. TO REINSTALL THE POWER PAD REPEAT THE STEPS ABOVE
4. TO REINSTALL THE POWER PAD REPEAT THE STEPS ABOVE
IN REVERSE ORDER.
IN REVERSE ORDER.
NOTE: CHECK TO INSURE THAT THE WIRES ARE NOT PINCHED
NOTE: CHECK TO INSURE THAT THE WIRES ARE NOT PINCHED
AGAINST THE CASTING DURING RE-INSTALLATION OF THE
AGAINST THE CASTING DURING RE-INSTALLATION OF THE
POWER PAD.
POWER PAD.
NOTE: BE SURE THAT THE “STREET SIDE” LABEL ON THE POWER
NOTE: BE SURE THAT THE “STREET SIDE” LABEL ON THE POWER
PAD IS ORIENTED WITH THE STREET SIDE OF THE UNIT AS
PAD IS ORIENTED WITH THE STREET SIDE OF THE UNIT AS
DEPICTED.
DEPICTED.
POWERPAD REMOVAL & INSTALLATION:
POWERPAD REMOVAL & INSTALLATION:
11.. TO OPEN THE FIXTURE, LOCATE THE TWO CLOSURE SCREWS.
TO OPEN THE FIXTURE, LOCATE THE TWO CLOSURE SCREWS.
THESE ARE LOCATED ON TWO ROUND BOSSES ON THE
THESE ARE LOCATED ON TWO ROUND BOSSES ON THE
STREET SIDE OF THE FIXTURE. (SEE FIGURE 1.)
STREET SIDE OF THE FIXTURE. (SEE FIGURE 1.)
2. UNSCREW THE TWO CAPTIVE CLOSURE SCREWS. YOU WILL
2. UNSCREW THE TWO CAPTIVE CLOSURE SCREWS. YOU WILL
KNOW
KNOW T
THE SCREWS ARE COMPLETELY DISENGAGED FROM
HE SCREWS ARE COMPLETELY DISENGAGED FROM
THE HOOD
THE HOOD WHEN
WHEN THE SCREWS CAN MOVE FREELY UP AND
THE SCREWS CAN MOVE FREELY UP AND
DOWN.
DOWN.
3. OPEN THE HOOD.
3. OPEN THE HOOD.
4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE
4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE HOOD AND RE-
HOOD AND RE-
TIGHTEN THE TWO CAPTIVE CLOSURE SCREWS.
TIGHTEN THE TWO CAPTIVE CLOSURE SCREWS.
NOTE FOR OPTIONAL
NOTE FOR OPTIONAL TRIGGER LATCH: TO OPEN THE UNIT
TRIGGER LATCH: TO OPEN THE UNIT
SIMPLY PULL
SIMPLY PULL BOTH TRIGGERS SIMULTANEOUSLY WITH YOU
BOTH TRIGGERS SIMULTANEOUSLY WITH YOUR
R
INDEX FINGER WHILE
INDEX FINGER WHILE PUSHING UP ON THE HOOD WITH YOUR
PUSHING UP ON THE HOOD WITH YOUR
THUMBS. CLOSE THE UNIT BY
THUMBS. CLOSE THE UNIT BY CLOSING THE HOOD AND PRESSING
CLOSING THE HOOD AND PRESSING
DOWN UNTIL THE TRIGGER LATCHES ENGAGE.
DOWN UNTIL THE TRIGGER LATCHES ENGAGE.
CAUTION
!
LIFT UNIT OUT OF BOX BY BAG, NOT CUPOLA
DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE.
HOUSING MUST BE GROUNDED TO REDUCE POTENTIAL OF ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
WARNING
!
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION,
CONSULT LOCAL CODE AUTHORITY
RISK OF FIRE. PRODUCT FOR OUTDOOR INSTALLATION AND USE ONLY.
WARNING
CAUTION
!
!
CUPOLA CAP
CUPOLA CAP
CUPOLA BASE
CUPOLA BASE
CLOSURE
CLOSURE
SCREW
SCREW
BOSS (2)
BOSS (2)
SCREW NOT
SCREW NOT
SHOWN
SHOWN
LOWER HOUSING
LOWER HOUSING
MIN POLE OD 2.375”
MIN POLE OD 2.375”
MAX POLE OD 3”
MAX POLE OD 3”
SET SCREWS (3)
SET SCREWS (3)
LADDER REST (2)
LADDER REST (2)
-OPTIONAL-
-OPTIONAL-
NEMA
NEMA
LABEL HERE
LABEL HERE
-OPTIONAL-
-OPTIONAL-
LENS
LENS
PANELS (4)
PANELS (4)
TRIGGER
TRIGGER
LATCH (2)
LATCH (2)
-OPTIONAL-
-OPTIONAL-
CUPOLA LENS
CUPOLA LENS
ADJUST PHOTO-
ADJUST PHOTO-
CONTROL BY LIFTING
CONTROL BY LIFTING
& TURNING CUPOLA
& TURNING CUPOLA
SIMULTANEOUSLY
SIMULTANEOUSLY
LAMP
LAMP
SOCKET
SOCKET
“STREET
“STREET
SIDE”
SIDE”
LABEL
LABEL
LENS
LENS
PANELS (4)
PANELS (4)
POWER
POWER
PAD
PAD
LOWER
LOWER
HOUSING
HOUSING
CAPTIVE
CAPTIVE
SCREW FOR
SCREW FOR
POWER PAD (4)
POWER PAD (4)
FIGURE 1
FIGURE 1
CLOSED HOOD - STREET SIDE VIEW
CLOSED HOOD - STREET SIDE VIEW
FIGURE 2
FIGURE 2
OPEN HOOD - TOP VIEW
OPEN HOOD - TOP VIEW
HOOD
HOOD
TM
