21
GB
English
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power tool
will move if kickback occurs.
Kickback will propel the tool
in direction opposite to the wheel’s movement at the point of
snagging.
d) Use special care when working corners, sharp edges etc.
Avoid bouncing and snagging the accessory.
Corners, sharp
edges or bouncing have a tendency to snag the rotating accessory
and cause loss of control or kickback.
e) Do not attach a saw chain woodcarving blade or toothed
saw blade.
Such blades create frequent kickback and loss of control.
Safety Warnings Specific for Grinding and Abrasive Cutting-
Off Operations:
a) Use only wheel types that are recommended for your
power tool and the specific guard designed for the selected
wheel.
Wheels for which the power tool was not designed cannot
be adequately guarded and are unsafe.
b) The grinding surface of the centre depressed wheels must
be mounted below the plane of the guard lip.
An improperly
mounted wheel that projects through the plane of the guard lip
cannot be adequately protected.
c) The guard must be securely attached to the power tool
and positioned for maximum safety, so the least amount
of wheel is exposed towards the operator.
The guard helps
to protect the operator from broken wheel fragments, accidental
contact with wheel and sparks that could ignite clothing.
d) Wheels must be used only for recommended applications.
For example: do not grind with the side of cut-off wheel.
Abrasive cut-off wheels are intended for peripheral grinding, side
forces applied to these wheels may cause them to shatter.
e) Always use undamaged wheel flanges that are of correct
size and shape for your selected wheel.
Proper wheel flanges
support the wheel thus reducing the possibility of wheel breakage.
Flanges for cut-off wheels may be different from grinding wheel
flanges.
f) Do not use worn down wheels from larger power tools.
Wheel intended for larger power tool is not suitable for the higher
speed of a smaller tool and may burst.
Additional Safety Warnings Specific for Abrasive Cutting-
Off Operations:
a) Do not “jam” the cut-off wheel or apply excessive pressure.
Do not attempt to make an excessive depth of cut.
Overstressing
the wheel increases the loading and susceptibility to twisting or
binding of the wheel in the cut and the possibility of kickback or wheel
breakage.
b) Do not position your body in line with and behind the
rotating wheel.
When the wheel, at the point of operation, is moving
away from your body, the possible kickback may propel the spinning
wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a cut for any
reason, switch off the power tool and hold the power tool
motionless until the wheel comes to a complete stop. Never
attempt to remove the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may occur.
Investigate
and take corrective action to eliminate the cause of wheel binding.
d) Do not restart the cutting operation in the workpiece. Let
the wheel reach full speed and carefully re-enter the cut.
The
wheel may bind, walk up or kickback if the power tool is restarted in
the workpiece.
e) Support panels or any oversized workpiece to minimize the
risk of wheel pinching and kickback.
Large workpieces tend to sag
under their own weight. Supports must be placed under the workpiece
near the line of cut and near the edge of the workpiece on both sides
of the wheel.
f) Use extra caution when making a “pocket cut” into existing
walls or other blind areas.
The protruding wheel may cut gas or
water pipes, electrical wiring or objects that can cause kickback.
Safety Warnings Specific for Sanding Operations:
a) Do not use excessively oversized sanding disc paper.
Follow manufacturers recommendations, when selecting
sanding paper.
Larger sanding paper extending beyond the
sanding pad presents a laceration hazard and may cause snagging,
tearing of the disc or kickback.
Safety Warnings Specific for Wire Brushing Operations:
a) Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress the wires
by applying excessive load to the brush.
The wire bristles can
easily penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or brush
with the guard.
Wire wheel or brush may expand in diameter due
to work load and centrifugal forces.
Additional Safety and Working Instructions
Always check the spindle lock button in fully released before swit-
ching on the tool! After using the spindle lock to tighten / loosen
the abrasive disk, it is possible that the button may stick in the
lock position. Whilst it may cause the tool or battery protection to
operate and remove power to the tool. Turn off the switch, remove
the battery then carefully rock the disk back and forth to release
the spindle lock button.
Note: If the battery protection has also activated, simply remove
the battery pack from the tool and replace it, thus resetting the
protection.
When grinding metal, flying sparks are produced. Take care that
no persons are endangered. Because of the danger of fire, no
combustible materials should be located in the vicinity (spark flight
zone). Do not use dust extraction.
Avoid flying sparks and sanding dust hit your body.
Never reach into the danger area of the machine when it is running.
Chips and splinters must not be removed while the machine is
running.
Immediately switch off the machine in case of considerable vibra-
tions or if other malfunctions occur. Check the machine in order to
find out the cause.
Under extreme conditions (e.g. smooth-grinding metals with the
arbour and vulcanized fibre grinding disk), significant contamina-
tion can build up on the inside of the angle grinder.
Do not let any metal parts enter the airing slots - danger of short
circuit!
WARNING! To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in fluid or allow a fluid to flow inside them.
Corrosive or conductive fluids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., Can
cause a short circuit.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Содержание BEWS18-115BL
