ADVANTEST R3765AG Скачать руководство пользователя страница 88

Страница: 88 / 446

R3765/67G Series Network Analyzer Operation Manual

5.1 Measurement of Transmission Characteristic (2 Trace Display)

5-4

•

By converting the format as follows, the measured results can be two-trace-overlap-
displayed.

Logarithmic magnitude/group delay measurement

Set the format to logarithmic magnitude (the first trace)/group delay (the second trace)
measurement.

[FORMAT]

{More 1/2}

{LOG MAG & DELAY}

The scale can be changed in the same way as

[SCALE]

{AUTO SCALE}

{TRACE 2nd/1st}

{AUTO SCALE}

The display on the screen is as follows.

Figure 5-3 Logarithmic Magnitude/Group Delay Measurement

(Overlap Display)

Содержание R3765AG































































































































































































































































































































































































































































Результаты поиска

Содержание R3765AG

Отзывы:

Похожие инструкции для R3765AG

Бренды по названию

Популярные бренды

ADVANTEST R3765AG, Руководство по эксплуатации

Результаты поиска

Содержание R3765AG

Отзывы:

Похожие инструкции для R3765AG

Бренды по названию

Популярные бренды