ADVANTEST R3765AG Скачать руководство пользователя страница 301

Страница: 301 / 446

R3765/67G Series Network Analyzer Operation Manual

7.15 Hard Copy

7-157

{DEFAULT SETUPS}

: See section 7.15.4. (This menu is for the printer. This

menu is not used at printer setup.)

{PLOTTER}

: See section 7.15.4. (This menu is for the printer. This

menu is not used at printer setup.)

Printer setup menu

{DPI}

: Sets the print resolution.

{UPPER MARGIN}

: Sets the upper margin in millimeters.

{LEFT MARGIN}

: Sets the left margin in millimeters.

{ZOOM SCALE}

: Specifies the enlargement ratio. Select it from either

one, two or three times.

{LANDSCAPE ON/OFF}

: Specifies the print direction (vertical or horizontal

writings).

{FORMFEED ON/OFF}

: Toggles the formfeed ON or OFF.

{PRINTER}

: Calls the printer menu. (See step

Printer menu

{ESC/P J84}

: Selects a printer which supports the printer control

code EPSON ESC/P J83 or J84 of the Seiko-Epson's
24-dot printer.

{ESC/P V.2}

: Selects a printer which supports the printer control

code EPSON ESC/P V.2 used for the Seiko-Epson’s
24/48-dot printer. If a printer which supports only the
raster mode is used, select this menu.

{PCL}

: Selects a printer (compatible with LaserJet 5L) which

supports the Hewlett Packard printer control code PCL.

{PRINT COLOR ON/OFF}

: Selects the color or monochrome output mode.

Содержание R3765AG































































































































































































































































































































































































































































Результаты поиска

Содержание R3765AG

Отзывы:

Бренды по названию

Популярные бренды

ADVANTEST R3765AG, Руководство по эксплуатации

Результаты поиска

Содержание R3765AG

Отзывы:

Бренды по названию

Популярные бренды