Advantech SmartMotion ST352 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 50

background image

SmartMotion ST352

6. First Use

6.1

Connecting the router before first use

Before putting the router into operation it is necessary to connect all components which

are required to run your applications. Don’t forget to insert SIM card.

The router can not operate without connected antenna, SIM card and power supply. If
the antenna is not connected, router can be damaged.

Figure 26: Router connection

29

«
...
33
34
35
36
37
...
»

Содержание SmartMotion ST352



















































Отзывы:

Нет отзывов

Похожие инструкции для SmartMotion ST352

Бренд: D-Link Страницы: 13

Бренд: Panasonic Страницы: 4

IntelliJack NJ200

Бренд: 3Com Страницы: 4

Бренд: Abus Страницы: 60

Elinx EIRP305-T

Бренд: B&B Electronics Страницы: 19

Бренд: Patton electronics Страницы: 51

Бренд: LaCie Страницы: 44

LaCie Ethernet Disk

Бренд: LaCie Страницы: 2

5big - Network NAS Server

Бренд: LaCie Страницы: 9

Бренд: LaCie Страницы: 14

12big Rack Fibre 8

Бренд: LaCie Страницы: 9

Бренд: Paradyne Страницы: 11

Бренд: Paradyne Страницы: 19

Бренд: Paradyne Страницы: 32

COMSPHERE 3550 Series

Бренд: Paradyne Страницы: 153

Jetstream CPX-1000

Бренд: Paradyne Страницы: 141

FrameSaver 9783

Бренд: Paradyne Страницы: 28

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды