Advantech SmartFlex SR305 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 63

background image

SmartFlex SR305

Figure 20: RS232-RS485-ETH & WiFi (plastic)

Figure 21: RS232-RS485-ETH & WiFi (metal)

5.2

HW Revisions

For the HW revision history, see the table below. The revision number is printed on the

packaging and product labels.

Rev.#

Description

1.0

Initial version (revision not printed on the labels).

2.0

New SIM slot type; see

for details.

Table 2: HW Revisions History

5.3

Delivery identification

Trade name

Product name

Description

SmartFlex SR305

SmartFlex

Router in a plastic or metal box

Table 3: Delivery identification

Figure 22: Label examples

13

«
...
18
19
20
21
22
...
»

Содержание SmartFlex SR305
































































Отзывы:

Нет отзывов

Похожие инструкции для SmartFlex SR305

Бренд: ABB Страницы: 66

Бренд: M2M Страницы: 9

PG-FLEX RT FRL-752

Бренд: PairGain Страницы: 6

Storagelibrary T24

Бренд: Tandberg Data Страницы: 28

Бренд: IBASE Technology Страницы: 39

Бренд: Comelit Страницы: 19

Бренд: Connectland Страницы: 10

airMAX NanoBridge M NBM3

Бренд: Ubiquiti Страницы: 24

Бренд: iNetVu Страницы: 20

Бренд: Planet Страницы: 20

Бренд: Digi Страницы: 75

Ultra WiFi Booster

Бренд: Optus Страницы: 8

Бренд: Steren Страницы: 130

X-Pedition XSR-1850

Бренд: Enterasys Страницы: 114

Бренд: Planet Страницы: 16

Бренд: Vivotek Страницы: 46

LN1000 - RELEASE NOTES 8-27-2010

Бренд: Juniper Страницы: 64

ReadyNAS Duo v2

Бренд: NETGEAR Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды