Advantech SKY-8101 Скачать руководство пользователя | Manualshive

Страница: 15 / 138

background image

___________________________________________________________________________________________________

SKY-8101 Manual V04 20180321

Copyright 2018 Advantech Co. Ltd. All rights reserved.

Page 13

1.1 Safety Instructions

Warning!

This section provides warnings that precede potentially dangerous procedures
throughout this manual. Instructions contained in the warnings must be
followed during all phases of operation, service, and repair of this equipment.
You should also employ all other safety precautions necessary for the
operation of the equipment in your operating environment.

Caution!

If you are not sure about the precautions applicable to your operating
environment, please contact your company

’s safety administrator. For basic

information you may also refer to the safety precautions per IEC704-1 listed
below although Advantech disclaims all responsibility for the accuracy of any
statements contained therein and its applicability for your specific
environment.

Failure to comply with these precautions or with specific warnings elsewhere in this
manual could result in personal injury or damage to the equipment.

Advantech intends to provide all necessary information to install and handle the
SKY-8101S in this manual. Because of the complexity of this product and its various
uses, we do not guarantee that the given information is complete. If you need additional
information, contact your Advantech representative.

The product has been designed to meet the standard industrial safety requirements. It
must not be used except in its specific area as specified in

Only  personnel  trained  by  Advantech  or  persons  qualified  in  electronics  or  electrical
engineering  is  authorized  to  install  service  or  maintain  the  product.  The  information
given in this manual is meant to complete the knowledge of a specialist and must not be
used  as  replacement  for  qualified  personnel.  Operating  personnel  must  not  remove
equipment covers. Only factory authorized service personnel or other qualified service
personnel  may  remove  equipment  covers  for  internal  subassembly  or  component
replacement or any internal adjustment.

Do  not  install  substitute  parts  or  perform  any  unauthorized  modification  of  the
equipment  or  the  warranty  may  be  voided.  Contact  your  local  Advantech
representative  for  service  and  repair  to  make  sure  that  all  safety  features  are
maintained.

1.1.1 Safety Precautions per IEC704-1

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Keep this equipment away from humidity.

4. Put this equipment on a reliable surface during installation. Dropping it or letting

it fall may cause damage.

5. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

«
...
13
14
15
16
17
...
»

Содержание SKY-8101











































































































































Отзывы:

Нет отзывов

Похожие инструкции для SKY-8101

Бренд: Razberi Страницы: 113

Бренд: Hi-flying Страницы: 29

Бренд: Buffalo Страницы: 2

NovaScale R410B F2

Бренд: Bull Страницы: 38

Бренд: IBM Страницы: 36

A+ AS-2124US-TNRP

Бренд: Supermicro Страницы: 130

Бренд: IBM Страницы: 90

Бренд: Auspex Systems Страницы: 52

Бренд: BITMAIN Страницы: 16

Бренд: Bosanova Страницы: 2

Бренд: Bosanova Страницы: 2

SuperStorageSystem SSG-2028R-DN2R40L

Бренд: Supermicro Страницы: 84

Бренд: Celestix Страницы: 68

Бренд: Supero Страницы: 80

Бренд: Intel Страницы: 31

ProLiant DL20 Gen9

Бренд: HP Enterprise Страницы: 124

Бренд: Uebo Страницы: 155

SuperBlade SBS-820H-420P

Бренд: Supermicro Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды