manualshive.com logo in svg

Advantech PPC-615W, Руководство пользователя

Поделиться
Скачать
Advantech PPC-615W Скачать руководство пользователя страница 49

41

PPC-615W/618W/621W User Manual

Chapter 2

System Installation and Setup

2.3

Mounting the System 

The panel PC supports various mounting options, as listed below:

Wall mounting

Arm mounting

Stand mounting

Panel mounting 

2.3.1

Wall Mounting

To mount the panel PC onto a wall, follow the instructions below.

1.

Select the location on the wall for the wall mount plate.

2.

Mark the locations of the two plate screws holes on the wall.

3.

Drill two pilot holes at the marked locations on the wall.

4.

Align the wall mount plate screw holes with the pilot holes.

5.

Secure the mount plate to the wall by inserting screws into the two pilot holes 

and tightening them.

Figure 2.1 Wall Mount Plate

Warning!

When mounting the panel PC, more than one person should perform the 

installation to prevent accidental damage to the panel or personal injury.
Le comité constate qu’el-nasr “mounting, Plus d’une personne installa

-

tion to prevent the cadre accidental damage to the personal injury.

Содержание PPC-615W



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды