Advantech POC-615 Series Скачать руководство пользователя страница 58

Страница: 58 / 64

POC-615 User Manual

8.1

Front Panel Function Buttons

Button Description

Power Button

Press this button to power on/off the device. When the device is on, this icon will emit

green light. When the device is off, the LED indicator will be off.

Reduce Volume

Press this button to reduce speaker and headphone volume.

Increase Volume

Press this button to increase speaker and headphone volume.

Disable Touch Function

Press this button to disable/enable touch function. When touch function is enabled,

this icon will emit green light. When touch function is disabled, the LED indicator will

be off.

Reading Light

Press this button to enable/disable the reading light.

Reduce Brightness

Press this button to reduce the LCD backlight brightness.

Increase Brightness

Press this button to increase the LCD backlight brightness.

Additional Functions

Press and hold both the reduce brightness and increase brightness buttons for half a

second to turn off/on the LCD backlight.
Turning the backlight off will not impact any program or the operation of the POC-615

terminal.
The backlight off function is useful for hospital and dark room environments because

it allows users to quickly turn off the backlight without affecting the system operation.
After a system restart, the backlight will automatically resume on status.

Содержание POC-615 Series

































































Результаты поиска

Содержание POC-615 Series

Отзывы:

Похожие инструкции для POC-615 Series

Бренды по названию

Популярные бренды

Advantech POC-615 Series, Руководство пользователя

Результаты поиска

Содержание POC-615 Series

Отзывы:

Похожие инструкции для POC-615 Series

Бренды по названию

Популярные бренды