Advantech PCI-1220U Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 56

Advantech PCI-1220U Скачать руководство пользователя страница 31

25

Chapter 3

3.9 External Pulse Control Input

The pulses output function of MCX312 chip is controlled by register set-
ting or by external pulse command input (nEXOP+, nEXOP-). There are
two output pulse mode for the external control pin. One is fixed pulse out-
put mode, and the other is continuous output mode. In PCI-1220U, it pro-
vides Jog and Hand wheel functions that allow you driving motors
through external Hand wheel or Jog equipment. In Jog mode, it is corre-
sponding to the “Continuous Output Mode,” and in Hand wheel mode, it
is corresponding to the “Fixed Pulse Output Mode.” These functions are
progressed without CPU involved on host PC. When the input signal is
enabled during fixed pulse drive, the pulse specified will be output. When
continuous output drive is enabled, the drive pulse will be continually
output at the period of signal Low. This signal should be used in combina-
tion with external power DC12 ~ 24V. The response time of circuitry
should take about 10 msec because of the delay of photo
coupled and RC filter.

Figure 3.14: External Drive Operation Signals

Figure 3.15: Example of Connecting to Jog

«
...
29
30
31
32
33
...
»

Содержание PCI-1220U

























































Отзывы:

Нет отзывов