Advantech PCI-1220U Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 56

Advantech PCI-1220U Скачать руководство пользователя страница 25

19

Chapter 3

3.4 General Purposed Output

The general purposed output nOUT3/DSND, nOUT2/ASND, nOUT1/
CMPM, and nOUT0/CMPP are from MCX312, and each output signal is
OFF status after system reset.

Figure 3.6: General Purpose Output

General purposed output signals used in motor drives can clear error
counter, alarm reset, stimulus off, etc., or select acceleration/deceleration
for driving, position counter, and the status of comparison register as your
output during driving.

3.5 Over Traveling Limit Switch Input

Note: When the axis/axes is/are about to stop (in the decelera-

tion stage), the axis/axes will not stop totally but keep
moving at a very low speed if you use S-curve accelera-
tion/deceleration to control speed under the “

Point to

Point

” and “

Line Profile(interpolation)

” drive mode

(positioning operation, specify a target position) on the
conditions below:
The hardware limit is activated and the

Limited Switch

Operation Mode

is set to “

Slow Down then Stop

” (WR2/

D2=1).
The software limit is enabled and activated (WR3/D, 1=1).
The

Limited Switch Function

of IN1 and IN2 are

enabled (WR1/D5, 3, 1=1).

«
...
23
24
25
26
27
...
»

Содержание PCI-1220U

























































Отзывы:

Нет отзывов