Advantech EKI-1526/N/I/TI Скачать руководство пользователя

Страница: 62 / 107

EKI-1526(TI) | 1528(TI) User Manual

4.4

USDG Control mode

In controlling mode, the EKI serial device server presents a modem interface to the

attached serial device: it accepts AT-style modem commands to connect / disconnect

to other networking device.
If you want a serial device running application program to connect/disconnect to

different devices on request, this function is available through the USDG Control

mode.

Figure 4.7 USDG Control Mode

Please refer to the USDG TCP/UDP server operating mode to setup the Data Listen

Port, Command Listen Port, and Data Idle Timeout.

4.4.1

Hangup Character

The default character is “+”. After you have connected to another serial device an via

EKI device, you may need to disconnect, using the command “+++”. To do this, press

“+” three times and wait for the idle timeout <default value is 100ms>; the device will

disconnect. You can set “Guard Time” to define the idle time.

4.4.2

Guard Time

The default value is 1000 ms.
Example: <Guard Time>+++<Guard Time>
Control Mode is designed for use with legacy operating systems, such as MSDOS,

that do not support TCP/IP Ethernet. By connecting one of the EKI’s serial ports to

the MS-DOS computer’s serial port, it is possible to use legacy software originally

designed to transmit data via modem, but now transmitting data over the Ethernet.

Command

Function

ATD <IP address><TCP

port><CR>

Forms a TCP connection to the specified host.

Ex: ATD 192.0.55.22:5201

In above example, the EKI serial device server forms a

raw TCP connection to the networking device

(192.0.55.22). The TCP port is 5201.

ATA <CR>

Answering an incoming call

+++<CR>

Returns the user to the command prompt when entered

from the serial port during a remote host connection.

Содержание EKI-1526/N/I/TI












































































































Результаты поиска

Содержание EKI-1526/N/I/TI

Отзывы:

Похожие инструкции для EKI-1526/N/I/TI

Бренды по названию

Популярные бренды

Advantech EKI-1526/N/I/TI, Руководство пользователя

Результаты поиска

Содержание EKI-1526/N/I/TI

Отзывы:

Похожие инструкции для EKI-1526/N/I/TI

Бренды по названию

Популярные бренды