Advantech EKI-1526/N/I/TI Скачать руководство пользователя

Страница: 59 / 107

EKI-1526(TI) | 1528(TI) User Manual

By disabling the Frame Break function, the series devices will wait for a “Response

Timeout” period, whether or not the device has transmitted data. During this period,

the host commands are queued and processed in the order received.
If Frame Break is enabled, the serial port idle is longer than the Frame Break period.

The EKI-1528 Series assumes the communication is completed and continues with

the next query. This is an efficient way to reduce waiting time and improve

performance.

4.3

USDG Data Mode

The EKI-1526(TI) | 1528(TI) Series can function either as Data server or Data client.

Both operations support TCP and UDP protocols. The Series allows you to treat your

serial devices as if they were networking devices. You can issue commands or

transmit data from serial devices, connected to a EKI-1526(TI) | 1528(TI) Series

device, to any devices that are connected to the Internet.

4.3.1

USDG TCP Client Mode

In TCP Client mode, the TCP connection is established from the EKI serial device

server. This operation mode supports a maximum of 16 simultaneous connections for

each serial port on EKI-15xx series to one host or several hosts. You can configure

the IP address and TCP port number of the network hosts connected to the EKI serial

device server using the Advantech Serial Device Server Configuration Utility. After

configuring the devices, when the EKI serial device server receives the data from the

serial port, and the device server connects to the hosts which are configured.

Figure 4.3 USDG TCP Client Mode

In USDG Data TCP Client mode, you may need to enable the peer numbers you

would like to receive. You can set a maximum 16 network devices to which you may

connect. You need to fill out the IP Address and Port (including local port and peer

port) of each network device to which you want to connect.

EKI-1526I

Console

Reset

PWR

Status

Serial

LAN 1

Speed

Link/Active

10 11

12 13

14 15

Ethernet 1

RS232/422/485

Ethernet 2

EKI-1526I

Содержание EKI-1526/N/I/TI












































































































Результаты поиска

Содержание EKI-1526/N/I/TI

Отзывы:

Похожие инструкции для EKI-1526/N/I/TI

Бренды по названию

Популярные бренды

Advantech EKI-1526/N/I/TI, Руководство пользователя

Результаты поиска

Содержание EKI-1526/N/I/TI

Отзывы:

Похожие инструкции для EKI-1526/N/I/TI

Бренды по названию

Популярные бренды