Advantech EKI-1526/N/I/TI Скачать руководство пользователя

Страница: 42 / 107

EKI-1526(TI) | 1528(TI) User Manual

3.4

Quick Tool Bar

The Advantech EKI Device Configuration Utility makes use of a Quick Tool Bar menu

to allow quick access to the management functions. See the following figure for

further information.

Figure 3.6 Quick Tool Bar Overview

Icon

Item

Description

Utility Settings

Clear to configure the general settings for the Main Form

Setting and Device Manager menus.

Refer to “Utility Settings” on page 29.

Configuration Wizard Start the software wizard (setup assistant) to lead you

through the VCOM configuration process for device server

product.

Clear Device List and

Search Again

Click to clear listed device servers in the Serial Device

Server List Area and initiate a new search.

NOTE: A continuous click of the icon results in the
following message: Please do not refresh so
frequently.

Search Again

Click to search for serial device servers on the local LAN.

Add IP Address to

Favorite

Click to include the selected IP Address into the Favorites

list group.

Search for a Range

of IP Addresses

Click to begin a range search. Enter the beginning and

ending IP addressed to being a search within the string

parameters.

Manual Direct

Mapping Virtual COM

Port

Click to add a target by selecting the Device Type and

inputting the IP address without physically connecting the

serial device server to the network.

Содержание EKI-1526/N/I/TI












































































































Результаты поиска

Содержание EKI-1526/N/I/TI

Отзывы:

Похожие инструкции для EKI-1526/N/I/TI

Бренды по названию

Популярные бренды

Advantech EKI-1526/N/I/TI, Руководство пользователя

Результаты поиска

Содержание EKI-1526/N/I/TI

Отзывы:

Похожие инструкции для EKI-1526/N/I/TI

Бренды по названию

Популярные бренды