Advantech EKI-1526/N/I/TI Скачать руководство пользователя страница 38

Страница: 38 / 107

EKI-1526(TI) | 1528(TI) User Manual

3.1

Configuration Utility Overview

Advantech EKI series serial device servers provide an easy-to-use utility to configure

your serial device server through an Ethernet connection. After the installation

program on the Advantech EKI Device Configuration Utility CD-ROM is finished, the

serial device servers are ready for use and configuration.
Advantech Serial Device Server Configuration Utility is an excellent device server

management tool. You can connect and configure the local and remote Advantech

serial device servers easily. The utility provides access to the following functions:



Configure the network settings (you can set the IP address, Gateway address,

and Subnet mask)



View the serial port parameters



Perform diagnostic tests (virtual COM port testing, port status list)



Upgrade firmware

3.2

Installing the Configuration Utility

Insert the Advantech EKI Device Configuration Utility CD-ROM into the CD-

ROM drive on the host PC.

Use Windows explorer or the Windows Run command to execute the setup

program; the name of the setup program on the CD-ROM is "EKI Device

Configuration Utility".

If there is an existing COM port mapping utility on the host PC, remove it at this

time. A system reboot may be necessary before continuing the installation.

Once the InstallShield Wizard screen displays, click

Next

to proceed with the

installation.

Figure 3.1 InstallShield Wizard 1 of 4

Note!

Microsoft .NET Framework version 2.0 or greater is required for this
application.

Содержание EKI-1526/N/I/TI












































































































Результаты поиска

Содержание EKI-1526/N/I/TI

Отзывы:

Бренды по названию

Популярные бренды

Advantech EKI-1526/N/I/TI, Руководство пользователя

Результаты поиска

Содержание EKI-1526/N/I/TI

Отзывы:

Бренды по названию

Популярные бренды