Advantech EKI-1526/N/I/TI Скачать руководство пользователя

Страница: 104 / 107

EKI-1526(TI) | 1528(TI) User Manual

7.4.10

monitor

Usage: monitor port [1|2|..] setting

Monitor COM port setting

Usage: monitor port [1|2|..] statistic

Monitor COM port statistic data

Usage: monitor port [1|2|..] ip

Monitor connected IP

7.4.11

time

Usage: time

Show current time informations.

Usage: time [YYYYMMDDhhmmss]

Set current time configuration.

Usage: time ntp [timeserver]

Set current time server configuration.

7.4.12

service

Usage: service telnet [enable|disable]

Enable/Disable telnet function

Usage: service snmp [enable|disable]

Enable/Disable SNMP function

7.4.13

mrfc2217

Usage: mrfc2217

Show all port mode and mode informations.

Usage: mrfc2217 [nn|all]

Set port [nn|all] as RFC2217 mode.

Usage: mrfc2217 [nn|all] idleto [] lsport []

Set host idle timeout(s) and listen port.

7.4.14

apply

Usage: apply

Save the settings to flash and reboot right now.

7.4.15

exit

Usage: exit

Terminate shell session

7.4.16

help

Usage: help [cmd]

Display help information of command cmd

7.4.17

reboot

Usage: reboot

Write settings and reboot the system immediately.

Содержание EKI-1526/N/I/TI












































































































Результаты поиска

Содержание EKI-1526/N/I/TI

Отзывы:

Похожие инструкции для EKI-1526/N/I/TI

Бренды по названию

Популярные бренды

Advantech EKI-1526/N/I/TI, Руководство пользователя

Результаты поиска

Содержание EKI-1526/N/I/TI

Отзывы:

Похожие инструкции для EKI-1526/N/I/TI

Бренды по названию

Популярные бренды