Advantech EKI-1242 Series Скачать руководство пользователя страница 38

Страница: 38 / 64

EKI-1242 Series User Manual

Insert a small flat-bladed screwdriver in the V1+/V1- wire-clamp screws, and

loosen the screws.

Insert the negative/positive DC wires into the V+/V- terminals of PW1. If setting

up power redundancy, connect PW2 in the same manner.

Tighten the wire-clamp screws to secure the DC wires in place.

Figure 2.21 Installing DC Wires in a Terminal Block

Align the terminal block over the terminal block receptor on the fieldbus

gateway.

Insert the terminal block and press it in until it is flush with the terminal block

receptor.

Tighten the screws on the terminal block to secure it to the terminal block

receptor.
If there is no gap between the terminal block and the terminal receptor, the

terminal block is seated correctly.

Figure 2.22 Securing a Terminal Block to a Receptor

2.8

Reset Button

Reset configuration to factory default:

Press and hold the Reset button for 5 seconds.

System reboot:

Press and hold the Reset button for 2 seconds.

Loosening

Wire-clamp

Screws

Installing DC

Wires

Securing

Wire-clamp

Screws

Note!

Do NOT power off the fieldbus gateway when loading default settings.

Содержание EKI-1242 Series

































































Результаты поиска

Содержание EKI-1242 Series

Отзывы:

Похожие инструкции для EKI-1242 Series

Бренды по названию

Популярные бренды

Advantech EKI-1242 Series, Руководство пользователя

Результаты поиска

Содержание EKI-1242 Series

Отзывы:

Похожие инструкции для EKI-1242 Series

Бренды по названию

Популярные бренды