Advantech EKI-1242 Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 64

background image

21

EKI-1242 Series User Manual

2.6

MicroSD Card Installation

The EKI-1242 Series provides an easy way to backup, restore, and deploy

configuration settings. The fieldbus gateway provides a microSD card slot to support

simple means to manage system configuration settings.
Only microSD cards with the FAT32 or exFAT file systems are supported.

2.6.1

Installing a MicroSD Card

1.

Before continuing, make sure the file system on the microSD card is set to

FAT32 or exFAT. If necessary, format the microSD card and then continue with

the procedure.

2.

Remove the screw securing the component cover.

Figure 2.9 Removing the Component Cover Screw

3.

Open the component cover.

Figure 2.10 Opening the Component Cover

4.

The microSD card has a beveled edge. Align the microSD card with the slot

making sure the card is aligned with the groove. If there is any resistance,

remove the card and re-align it to the slot.

5.

Insert the microSD card and press it in until an audible click sounds.

Figure 2.11 Installing the MicroSD Card

«
...
30
31
32
33
34
...
»

Содержание EKI-1242 Series

































































Отзывы:

Нет отзывов

Похожие инструкции для EKI-1242 Series

Бренд: Pathport Страницы: 3

Бренд: Zero 88 Страницы: 16

Бренд: Symantec Страницы: 2

Бренд: Cellio Страницы: 9

Бренд: SerVision Страницы: 40

Бренд: B&B Страницы: 2

Бренд: ADI Страницы: 56

Бренд: Microhard Systems Страницы: 186

SIMATIC IOT2020

Бренд: Siemens Страницы: 2

SIMATIC IOT Gateway MQTT

Бренд: Siemens Страницы: 2

MindConnect Nano

Бренд: Siemens Страницы: 2

Instabus/DALI Gateway N 141

Бренд: Siemens Страницы: 5

SIMATIC IOT2050

Бренд: Siemens Страницы: 25

GAMMA 5WG1 143-1AB01

Бренд: Siemens Страницы: 2

Бренд: Siemens Страницы: 6

Бренд: Siemens Страницы: 8

Бренд: Siemens Страницы: 20

SIMATIC PN/M-Bus LINK

Бренд: Siemens Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды