manualshive.com logo in svg

Advantech B+B SmartWorx SmartMotion ST355, Руководство пользователя, Страница: 18 / 48

Поделиться
Скачать
Advantech B+B SmartWorx SmartMotion ST355 Скачать руководство пользователя страница 18

SmartMotion ST355

5.4

Basic dimensions of the router box

Figure 9: Basic dimensions of the router box

5.5

Mounting recommendations

•

Possibility to be put on a work surface,

•

DIN rail EN 60715 with included metal clip.

For the most of applications with a built-in router in a switch board it is possible to recognize

two kinds of environments:

•

No public and industry environment of low voltage with high interference,

•

Public environment of low voltage without high interference.

For both of these environments it is possible to mount router to a switch board, the following

there is no need to have examination immunity or issues in connection with EMC according to
EN 61439-1:2011.

Attention:

If the negative pole of the router is grounded, there is no protection against

reversed polarity!

Compliance of EN 61439-1:2011 specification it is necessary to observe next assembly
of the router to the switch – board:

•

For whip antennas we recommend to observe a distance of 6 cm from cables and metal
surfaces on every side due to the elimination of interference. While using an external
antenna except for the switch-board it is necessary to fit a lightening conductor.

•

Before mounting a router on sheet-steel we recommend using a "cable" antenna.

•

For every cables we recommend to bind the bunch, we recommend for this use:

12

Содержание B+B SmartWorx SmartMotion ST355

















































Отзывы:

Нет отзывов