manualshive.com logo in svg

Advantech B+B SmartWorx SmartMotion ST355, Руководство пользователя, Страница: 34 / 48

Поделиться
Скачать
Advantech B+B SmartWorx SmartMotion ST355 Скачать руководство пользователя страница 34

SmartMotion ST355

6.2

Start

The router is put into operation when the power supply is connected to this router. By

default, the router will automatically start to log on to the default APN. DHCP server will start
to assign addresses for devices on the Ethernet port ETH0. Router behavior can be changed
via the web interface. This is described in detail in the

Configuration manual for SmartMotion

routers

.

6.3

Configuration

Attention!

If no SIM card is inserted in the router, it is not possible to operate. Inserted

SIM card must have activated data transmission.

6.3.1

Configuration over web browser

For status monitoring, configuration and administration of the router is available a web

interface which can be accessed by entering the IP address of the router into the web browser.
The default IP address of the router is 192.168.1.1.

Attention, it is necessary to use HTTPS

protocol for secure communication over a network!

Figure 28: Entering the IP address of the router

Configuration may be performed only by the user "root" with default password "root".

Figure 29: Entering login information

28

Содержание B+B SmartWorx SmartMotion ST355

















































Отзывы:

Нет отзывов