Advantech B+B SmartWorx SmartMotion ST355 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 48

Advantech B+B SmartWorx SmartMotion ST355 Скачать руководство пользователя страница 16

SmartMotion ST355

5.3

Order codes

Order codes overview is shown in the table below.

Product Name

Order code

Features – interfaces

ST355

BB-ST3550x0yz

∗

2x LTE module (1x LTE 450 MHz), 2x ETH, 1x USB,
2x BI, 1x BO, 1x microSD reader, 4x SIM reader

ST355

BB-ST3551x0yz

∗

2x LTE module (1x LTE 450 MHz), 2x ETH, 1x USB,
2x BI, 1x BO, 1x microSD reader, 4x SIM reader, WiFi

Table 3: Order codes overview

∗

Replace the letters "x", "y" and "z" with the values from the following tables:

Letter "x" – Power over Ethernet (PoE)

Power over Ethernet (PoE)

Number "x" in code

Version without PoE

0

PoE PSE – Power Source Equipment – powers other devices

8

PoE PD – Powered Device – can be powered via Ethernet

9

Table 4: Power over Ethernet

Letter "y" – type of the router box

Type of box

Number "y" in code

Metal

2

Table 5: Type of router box

Letter "z" – type of the power supply connector

Type of power supply

Number "z" in code

International (4 plugs)

5

Without accessories

0

Table 6: Type of power supply

10

«
...
14
15
16
17
18
...
»

Содержание B+B SmartWorx SmartMotion ST355

















































Отзывы:

Нет отзывов