Advantech AIIS-1882 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 38

background image

AIIS-1882 User Manual

6

2.1

Installation

Assembly with AIIS-3411

To assemble the AIIS-1882 board in the AIIS-3411 computer, you should

1.

Open the enclosure, screw sets and the front panel

2.

Assemble the AIIS-1882 board in the chassis, lighting cables to the front panel,

finally the I/O panel back to the front panel

Please follow the steps below to open the enclosure, screw sets and the front panel:

1.

Remove the screws on the rear side of AIIS-3411

2.

Remove the top enclosure of AIIS-3411

3.

Remove 4 screws around the expansion connectors

4.

Remove the screws of the I/O panel

5.

Remove I/O panel

Figure 2.1 Disassembling the enclosure of AIIS-3411

Then, assemble the AIIS-1882 board in the chassis, lighting cables to the front panel,

finally the I/O panel back to the front panel:

1.

Screw the four screw posts back into the holes that they came from.

2.

Remove the release paper from the supporting pad, then stick it onto the place

indicated in figure 2.4.

3.

Place the AIIS-1882 into the chassis, then press to connect the board-to-board

connector right onto the top of the assembly.

4.

Affix the screws back to the board on the corners.

«
...
14
15
16
17
18
...
»

Содержание AIIS-1882







































Отзывы:

Нет отзывов

Похожие инструкции для AIIS-1882

Бренд: FAAC Страницы: 14

Бренд: Febco Страницы: 4

Бренд: Cisco Страницы: 48

Бренд: Ransburg Страницы: 49

Бренд: Balboa Страницы: 2

Бренд: Badger Meter Страницы: 20

HomeTec Pro CFF3000

Бренд: Abus Страницы: 13

Бренд: NAVITAS Страницы: 7

Бренд: Abus Страницы: 2

Бренд: Vanderbilt Страницы: 2

Бренд: Zennio Страницы: 30

Бренд: Zeta Страницы: 13

Бренд: Lab.gruppen Страницы: 2

NOVASTAT EL DIGITAL

Бренд: Taconova Страницы: 7

Бренд: IFM Страницы: 41

Бренд: Duco Страницы: 16

Бренд: M-system Страницы: 7

Бренд: Texecom Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды