Advantech Wireless SSPBMg-C400-BRE Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 46

Advantech Wireless SSPBMg-C400-BRE Скачать руководство пользователя страница 23

SSPBMg-C400-BRE

4.2 REDUNDANT INTERFACE

The

Redundant Interface

connections are made with a 10-pin circular connector mounted on

the SSPB enclosure. The connector type is listed in

TABLE 5

at page 17 and the location is

shown in

Figure 4

at page 16. A redundant system cable is provided with the redundancy kit

that provides the interconnection between the two SSPB units and the waveguide switch in a
redundant configuration.

This interface is not used for standalone units.

4.3 LED

TX

: green/red LED indicating the state of the transmission path.

•

If this LED is not lit, the unit is not powered (or the power supply failed).

•

If this LED is RED lit, it indicates that the unit is in FAULT or ALARM condition.

•

If this LED is blinking GREEN, it indicates that the unit is in MUTE state (following a
MUTE command).

•

If this LED is GREEN lit, it indicates that the unit is functioning properly.

4.4 RF OUTPUT MONITOR INTERFACE

This RF output sample port is located at the RF MON connector, which is mounted on the SSPB
enclosure. The type of mounting connector is listed in

TABLE 5

at page 17 and the location is

shown in

Figure 4

at page 16. This interface is used for the independent monitoring of the SSPB

output.

A table of the coupling factor versus the frequency is provided with each unit. Note that

because this port is located before the band-pass filter (BPF) the signal on this port may contain
spurious signals and harmonics. This port should only be used for output power monitoring (via
an external power meter) or should be kept capped if not used.

Page

22

«
...
21
22
23
24
25
...
»

Содержание SSPBMg-C400-BRE















































Отзывы:

Нет отзывов