Advanced Axis D9068 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 52

Advanced Axis D9068 Скачать руководство пользователя страница 27

www.advancedco.com

27

www.advancedco.com

27

Table 5

lists the event history abbreviations.

Table 5: Event History Abbreviations

Abbreviation Meaning

A, ALRM

Alarm

AUTOTST Auto

test

ARST Alarm

restore

BATT:LOW Battery

low

BAT:RSTR Battery

restore

COMM Communication

DATALOST Data

lost

EE2 EEPROM

F Fire

FLT Fault

KEYPD: IN

Keypad installed

KEYPD: RS

Keypad removed

M Monitor

MANULTST Manual

test

SER:FL

Panel communication failure

OFFNORM

Off normal at test

PGMG:FLT Trouble

programming

PH1

Phone Line 1

PH2

Phone Line 2

RS,RST,RSTR Restore

S Supervisory

SYSFLT:F Trouble

input

SYSFLT:R

Trouble input restore

SYS:RSET System

reset

SYSTRB System

trouble

WDOG:RST

Automatic CPU reset

(watchdog)

TRBL Trouble

TRST Trouble

restore

W Waterflow

alarm

SER:RS

Panel communication restore

4.3 Reset

Reset the D9068P in one of four ways:
1. At the DACT-PRG LCD Remote Keypad, press [4] to

select

Reset

from the Main Menu or press [Reset].

Pressing either key resets the D9068P only when off-
normal conditions are present. The system sends an
Open Reset Report with the user ID parameter of 99.

2. Exiting the Test Mode. The system sends an Open

Reset Report with the user ID parameter of 99.

3. Exiting the Programming Mode. The system sends an

Open Reset Report with a user ID parameter of 01.

4. Powering up the D9068P, No Open Reset Report is

sent.

5 Programming

5.1 Using the Keypad

All programming for the D9068P is done using the
DACT-PRG LCD Remote Keypad. To properly program
the D9068P, you must always press the [* Command] and
[* Clear] keys in addition to the key(s) necessary to make
specific programming entries.
• Press [# Command] to accept an entry into the

D9068P.

• Press [* Clear] after pressing [* Command] to return to

the submenu or menu selections.

Refer to

Figure 18

for the complete programming key

sequence for setting the D9068P operational date.

Note: Events received from the AX Series
Intelligent Fire Alarm Control Panel over the
serial connection are not stored in the history
buffer these events are stored in the AX Series
FACP history buffer.

«
...
25
26
27
28
29
...
»

Содержание Axis D9068





















































Отзывы:

Нет отзывов