manualshive.com logo in svg

Advanced Axis D9068, Руководство по установке и эксплуатации, Страница: 18 / 52

Поделиться
Скачать
Advanced Axis D9068 Скачать руководство пользователя страница 18

 

 

www.advancedco.com

18

3.1  AX Series Intelligent Fire Alarm Control Panel and D9068P Power up 

In addition to the power up requirements of the AX Series Intelligent Fire Alarm Control Panel, the following should 
be performed with systems that include a D9068P DACT. 

3.1.1  Before Powering up 

Before applying power to the AX Series FACP, verify: 

• 

That all connections made to the AX-SEB have been done according to this document. 

• 

That all connections made to the D9068P have been made according to this document. 

• 

That all telephone connections have been made to the D9068P according to this document. 

• 

That both RJ31X male connectors are firmly seated in the RJ31X female connectors located on the D9068P 
DACT. 

3.1.2  After Power up 

After power is applied to the AX Series Intelligent Fire Alarm Control Panel, verify the following D9068P conditions 
occur: 

• 

All D9068P LEDs briefly light. 

• 

The D9068P System Trouble LED lights. 

• 

The D9068P Heartbeat LED flashes to indicate the D9068P is functional. 

3.2 D9068P 

Quick 

Start 

Upon power up, the D9068P will be in a trouble condition and will not function properly, nor will the D9068P be 
supervised by the AX Series Intelligent Fire Alarm Control Panel until the following steps are performed: 

1.   Program the D9068P. 

2.  Assign account numbers to the D9068P. 

3.  Assign telephone numbers to the D9068P. 

4.  Program the AX Series Intelligent Fire Alarm Control Panel for serial DACT communications. 

 

 

 

To program the D9068P and the AX Series Intelligent Fire Alarm Control Panel for proper operation, refer 
to the programming section 5 of this manual. 

If the D9068P is correctly programmed and input wiring is properly connected, only the Heartbeat LED 
should be flashing.  This indicates a normal D9068P operation. 
 
To verify correct communications of the D9068P, perform a manual Communications Test.  Refer to 
section 5.5.4 1: TEST COMM on page 40 for manual communications testing instructions. 

Test according to NFPA 72 following modifications, repairs, upgrades, or adjustments to the AX Series 
Intelligent Fire Alarm Control Panel and/or D9068P DACT. 

Refer to Appendix B beginning on page 44 for information on error messages or messages indicating 
abnormal operating conditions. 

Содержание Axis D9068





















































Отзывы:

Нет отзывов