Advanced Illumination DCS-400E Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 22

Advanced Illumination DCS-400E Скачать руководство пользователя страница 22

Page

22

of

22

Warranty Information

Every Advanced illumination, Inc. (Ai) product is thoroughly inspected and tested
before leaving the factory. Products are warranted to be free of defects in
workmanship and materials for a period of five years from the original date of
purchase. Should a defect develop during this period, please contact Ai Customer
Service or your Ai distributor for a Return Merchandise Authorization (RMA), and return
the complete product, freight prepaid, to Ai. Please provide a detailed description of
the problem if possible. If a defect is found, Ai will - at our discretion - repair or replace
the product without charge. Ai claims no liability for any implied warranties, including
“merchantability” and “fitness for a specific purpose.”

Customer Support and Product Information

Standard Product Information:

www.advancedillumination.com

Customer Service Inquiries:

[email protected]

440 State Garage Road, Rochester VT. 05767

© 2019 Advanced Illumination Inc. All rights reserved

«
...
20
21
22

Содержание DCS-400E























Отзывы:

Нет отзывов